When the Separator Gets Louder: A Diagnosis in Order
Owners rarely describe a separator as loud in absolute terms. They say it is louder than it used to be, and that comparison is the useful piece of information. A machine that has run quietly for two seasons and now hums is telling you something changed; a machine that has always sounded the same is probably fine regardless of how it sounds to a visitor.
So the first step costs nothing: write down what normal sounds like while it is still normal.
Four causes, in the order worth checking
Noise on a separator comes from a small number of places. Checking them in this order takes minutes and avoids opening the bowl to look for a problem that is underneath the bench.
### 1. Something is loose or touching
The cheapest explanation and the most common after cleaning or transport. A spout that is not seated, a cover sitting slightly off, a tool left on the frame, a cable touching the housing. Loose parts rattle at the running frequency and are loudest at start-up.
Check: run the machine empty for a few seconds and press a hand lightly on the cover, the spouts and the frame in turn. If the sound changes when you touch something, you have found it.
### 2. The machine is standing on something that amplifies it
A separator on a thin steel bench, a wooden table that has dried and loosened, or a floor with a hollow beneath it will sound much louder than the same machine on a solid base. This is not a fault in the machine, and it gets worse over time as fastenings loosen.
Check: the mountings and the surface. Hardened or compressed mounting bushes transmit vibration instead of absorbing it; the anti-vibration mount set is a consumable in the same sense as a gasket.
### 3. The bowl is not sitting as it did
If the bowl was cleaned, reassembled or transported, uneven seating shows up as a low, once-per-revolution sound rather than a rattle. It is usually accompanied by a slight vibration you can feel through the bench.
Check: the bowl is fully seated, the locking nut is tight, and the disc stack is in the right order. A stack that is not fully seated changes both the sound and the separation result.
### 4. A bearing is going
This is the one that matters, and it is usually the last to appear. Bearing noise is continuous, changes with speed rather than with load, and does not respond to pressing on covers. If the sound continues for a moment after the machine is switched off and slows down, that is worth attention.
Check: with the machine off and the bowl removed, turn the spindle by hand. It should turn freely and quietly. Roughness, a dry sound, or play is a reason to stop using the machine until it is looked at, not a reason to run it a little longer.
What the sound itself suggests
| What you hear | Most likely | First check |
|---|---|---|
| Rattle, worst at start-up | Loose cover, spout or fitting | Press components while running |
| Once-per-revolution knock | Bowl seating or stack order | Bowl seat and locking nut |
| Continuous hum, worse with speed | Bearing or mountings | Turn spindle by hand; inspect bushes |
| Whole bench resonates | Stand or floor | Mountings and surface rigidity |
| Rattle only with milk | Air intake or feed | Feed control and float valve |
The last row is worth separating: a noise that only appears when milk is flowing is about the feed path, not the rotating assembly. The symptom-to-part map covers that direction in more detail.
What not to do
Do not keep running a machine to see whether the noise settles. Noise from a bearing does not improve, and the cost of a bearing is small next to the cost of a damaged spindle.
Do not tighten everything as a first response. Over-tightening the bowl nut or the mountings introduces a new problem while hiding the original one.
Do not diagnose by ear over the telephone. Record a short video with the machine running and the microphone close to the frame - the difference between a rattle and a bearing is obvious in a recording and impossible to convey in words.
A note on baselines
The single most useful maintenance habit for noise is a recording made when the machine is new or freshly serviced: thirty seconds of it running empty, filmed from the same place each time. Comparing this month against that recording answers in seconds what a description cannot.
Keep the recording with the service records so the date and the work done at the time are attached to it.
Related maintenance resources
Use the ANDUUK replacement parts catalog to match seals, discs, outlets, motor components and cleaning tools to the correct machine assembly.
Browse replacement parts · Read the cleaning and reassembly checklist · Read separator FAQs